Kuppersbusch washing machine quickly took pride of place in the line of luxury household appliances.
Like many washing machines, Kuppersbush is equipped with the most accurate high-speed self-diagnosis system. This system instantly detects problems with parts, wiring or electronics and reports this using error codes. Fault codes are displayed on the electronic scoreboard, while past generations of cars have signaled the problem with combinations of flashing lights.
Next, we will talk about what the codes of breakdowns mean, what to do when they are detected, and how to troubleshoot.
Important! If you ignore the code and reset the errors by rebooting the machine, sooner or later this can lead to the breakdown of one or several nodes: the pump, heater, sensors, and maybe even the control board.
Fortunately, the Kuppersbush washing machine is still elite, because breakdowns are rare for it. The main thing is to react in time to the detected problem and eliminate it.
The following is an accurate Kuppersbusch CMA error table. Understanding what each of them means, you will be able to provide all possible assistance to your typewriter in time when it issues an error.
What do SM Coopersbush codes mean, what to do to eliminate them
Code | Value | Solving the problem and the cause of the breakdown |
Ef1 | The machine shows the error EF1 when the drainage system is clogged. | It is necessary to clean all the elements of the drain system: drain filter, drain hose, drain pump. |
Ef2 | The machine shows on the display EF2 when foaming is too high. | It may be worth changing the detergent to a better one or choosing a different washing mode. |
E11 | The washing machine gives out E11 when it detects problems with the intake of water for washing. This is accompanied by the fact that more time is spent on water intake than usual. | Perhaps the blockage of the filler system has occurred, the filler valve has broken or there is simply no water or sufficient pressure in the water supply. |
E12 | Crash during water filling in drying mode. | Problems with the bay system or main board. |
E21 | If E21 is displayed, then the water drain is broken. | Blockage in the drain system, or breakdown of the pump. |
E22 | E22 lights up on the display in the absence of draining water in the drying mode. | Drain system problems, breakdown of the control module. |
E31, E32 | Too little or too much water is collected in the tank. | To eliminate E31 or E32, it is necessary to check the water level sensor and its nozzles. |
E33 | E33 can mean two failures at once: heater malfunction (heater) or SM reaction to a power surge. | It is necessary to check the heater: it may have accumulated scum on it, and it must be cleaned or replaced. In case of power surges, turn off the power to the CM, check the wiring. You may need to change the power cord or surge protector. |
E41, E42, E43, E44, E45 | All these error codes - from E41 to E45 - appear when the hatch lock device malfunctions. | You may have to change the UBL. But first, just try closing the hatch more tightly. |
E51 | E51 indicates a module failure. | Repair or replacement of the controller may be required. |
E52 | The board does not receive signals from the tachogenerator. | Most likely, the tachogenerator is defective, therefore, needs to be replaced. You will need to disassemble the housing and remove the engine. |
E53 | E52 also indicates a failure in the module. | Need firmware or board replacement. |
E54 | Error E54 lights up on the screen when the relay located on the module malfunctions. | Relay replacement is required, i.e. board repair. |
E61 | Water is too slow. | To remove the error E61, it is necessary to check the heater. It could scum, which is why it loses its thermal conductivity. Such a heater quickly burns out, so it may be necessary to replace the heater. |
E62 | E62 also indicates a heater malfunction, but is associated with water overheating. | It is necessary to replace the heater or check the health of the temperature sensor. |
E66 | The E66 code indicates a breakdown of the heater relay or the heater itself. | Replacement of broken parts is required. |
E71 | E71 indicates a breakdown of the thermistor. | Need replacement thermistor. |
E72, E73 | Errors E72 and E73 occur when the drying thermistor fails. | Replacing the thermistor will solve the problem. |
E91 | As a rule, the E91 code indicates a communication failure between the control panel indicators and the module. | Parsing the machine is required: checking the contacts and the board itself. |
Now you know how to fix this or that error. Even if you can’t do it yourself, understanding what the error code means, you can quickly and clearly explain what happened to the master.
As a result, the repair will be done on time, and the machine will work properly for many years to come.