No matter how carefully you relate to your Samsung washing machine, over time, problems arise in the system. Contacting a service center is an expensive pleasure, especially since most breakdowns can be fixed on your own.
We will figure out how to repair a Samsung washing machine (Samsung) with our own hands.
What malfunctions are typical for SM Samsung
The design of the Samsung washing machine is of high-quality assembly, especially for electronics.
According to service centers, electronic parts - circuit board, wiring - fail much less frequently than other elements.
Let's consider in more detail:
Samsung error codes
By highlighting the trouble codes on the display, the system informs the user about the problem. You need to understand the meaning of the error codes of the Samsung washer and proceed with the repair yourself.
Fault Codes | What do they mean |
---|---|
1E | Failure of the pressure switch. |
3E, 3E1, 3E2, 3E3, 3E4 | SM motor tachometer malfunction. |
4E, 4E1, 4E2 | There is no water in the tank. |
5E | Error draining water. |
8E | Failure of the SMA electric motor. |
9E1, 9E2, Uc | Mains error. Too high or low voltage. |
AE | There is no connection between the electronic board and the display panel. |
bE1, bE2, bE3 | The washing machine does not turn on. |
CE | The water in the tank exceeded the heating rate. |
bE1, bE2, bE3 | Problems with closing the hatch door. |
FE | The ventilation is not functioning. |
NOT, NOT1, NOT2, NOT3 | Defective heating element (heater). |
LE (LE1) | There was a leak. |
OE (OF) | Too much water in the tank. |
tE1, tE2, tE3 | The temperature sensor is defective. |
HER | Failure of the heating element or drying temperature sensor. |
UE | An imbalance has arisen. |
Sud | Exceeded foam concentration. |
Troubleshooting
Consider how to repair a Samsung washing machine with your own hands.
Samsung car does not pump water
It is necessary to check the drainage system: most often the cause is a blockage in the drain pipe or pump.
- Unplug the machine, turn off the water.
- Disconnect all communications.
- Remove the dispensing tray by pressing the lock in the center.
- Open the drain filter hatch on the front panel from the bottom.
- Drain the remaining water and clean the filter.
- Put the SM on its side, open access to the bottom.
- Having found the location of the pump and pipe, loosen the pipe clamps.
- Disconnect the pump wires.
- Remove the screws that secure the pump.
- After removing the pump, check for blockage.
- Remove the pipe and flush it from dirt.
Carefully inspect the pipe for damage. Most often, it loses tightness at the mounting points of the clamp. If the pipe or pump malfunctions, new elements must be installed.
No heat
To check and replace you need to get to the heater. By the way the Samsung washing machine is arranged, we conclude: in order to get a heater, you need to remove the front housing of the washer.
We carry out the repair of the washing machine automatically:
- After disconnecting the CM from the mains, unscrew the screws that secure the top panel at the back.
- Pull out the dispensing tray. Remove the bolts located behind it.
- Remove the remaining mounting bolts and remove the control panel of the Samsung washing machine.
- Remove the bottom panel.
- Bending the cuff of the hatch, pry the metal clamp and remove it.
- Remove the cuff inside the drum.
- Unscrew the door lock screws and disconnect the wires, remove the front panel.
- At the base of the drum is a heater.
- Disconnect heater wires.
- Loosen the center nut (not completely).
- Having pressed the central bolt inside, get the heater.
- Pull the thermostat out of the heater.
If the thermostat is working, just rearrange it in a new heater. Installation is carried out in the reverse order, after which the housing is placed.
Does not pick up water or flood a lot of water
The reason for the lack of water may be clogged. Repairing a washing machine with your own hands, first of all:
If an excessive amount of water enters the machine, check the filler valve.
- After removing the top panel of the SM, on top of the wall you will see the inlet valve.
- Disconnect valve wires.
- Turn off fixing bolts.
- After loosening the clamps, disconnect the hoses.
If the valve as a whole is working, replace the rubber bands. If not, install a new part.
Drive belt wear
To replace the belt, you need to know how to remove the back wall of the Samsung washing machine:
- Having unscrewed bolts, remove the back panel.
- Remove the old belt from the pulley.
- If inspection confirms belt wear, install a new element.
- Start putting the belt on the engine pulley by moving and scrolling the drum pulley.
Now you know how to repair the washing machine without calling the wizard.
Noisy Samsung Car
When washing, the SM began to vibrate strongly, buzz, make noise? Check the installation, how stable the equipment is on the floor.
AGR does not respond to button presses, does not turn on
The reason may be in the control panel. It is necessary to check the contacts of all buttons, maybe they are stuck, or the keys themselves were sold.
Another problem is the electronic board. Repair of the control module in the Samsung washing machine is not an easy task, so it is better to contact a service center. Of course, before contacting you can examine the board yourself:
- After removing the top cover, pull out the detergent drawer.
- Remove the screws holding the control panel.
- Unclench plastic latches and disconnect wires.
- Having opened the latches of the unit, remove the cover and remove the board.
Visible damage can be highlighted by burned-out elements, paths. If visually nothing is noticeable, contact the service.
Having studied typical malfunctions, you learned how to repair and repair your Samsung Samsung washing machine.